• The .xml file had to be hand-edited due to a bug in coorsim.
• This list has not been run online yet.

• The .xml file had to be hand-edited due to a bug in coorsim.
• This list was tested online during runs 207728-207740.

• The .xml file had to be hand-edited due to a bug in coorsim.
• This list was tested online during runs 207220, 207221, and 207222

• The .xml file had to be hand-edited due to a bug in coorsim.
• This list went online on March 29, 2005, run 205021.

• The .xml file had to be hand-edited due to a bug in coorsim.
• This list went online on March 12, 2005, run 204684.

• The .xml file had to be hand-edited due to a bug in coorsim.
• This list went online on Dec. 15, 2004, run 202025.

• The .xml file had to be hand-edited due to a bug in coorsim.
• This list should be funtionally no different than v13.21. The only difference is the reordering of the L3 filters so that event processing should be faster

• The .xml file had to be hand-edited due to a bug in coorsim.

• The .xml file had to be hand-edited due to a bug in coorsim.
• This list was created for use with the trigger rate tool. It contains only skeletal Level 1 and Level 2 triggers, but has many generic Level 3 triggers that could be used as a starting point for rate studies or new trigger contruction. It will be used as a basis for the creation of the Level 3 portion of the next TrigSim trigger list to be run on the MC farms.

• The level1.sim file had to be hand-edited due to a bug in coorsim.

• The level1.sim file had to be hand-edited due to a bug in coorsim.

tsim_p13-1.20-data.tar

tsim_p13-1.20_toollist.txt

• this is the first triggerlist which is L3 compatible in p13. It will be made into the default list for d0trigsim. In p13->p13.04.00 the default list will not properly configure L3.
• -mc corresponds to making the level2.sim-stripped correction and changing the level3.sim geometry management, CFTunp and SMTunp settings. The L3 geometry is set to p11.08.00, edit this line yourself if your inputs are different. The settings of level3.sim are the same as for global_CMT 9.30 below....and need review by an L3 expert as well....
• -data corresponds to making the level2.sim-stripped correction and leaving level3.sim alone.
• A toollist.txt is provided which corresponds to this triggerlist but with the L3 unpack tools removed. Until we get a new version of Heptuple in p13 use this toollist to greatly reduce the crashes when producing the ntuple. Use the -l3toolist commandline option to pass this list to the executable.

global_CMT-9.30-data.tar

global_CMT-9.30_toollist.txt

• -mc corresponds to making the level2.sim-stripped correction and changing the level3.sim geometry management, CFTunp and SMTunp settings. The geometry is set to p11.08.00, edit this line yourself if your inputs are different. NOTE: I know I made the right fix to level2.sim-stripped....however I edited level3.sim so that results came out....no L3 expert has yet verified the correctness of the edits:

          GEO L3GeometryManagement(
                  tooltype="utility",
                  MCTag="p11.08.00")|
  
          CFTUnp L3TCFTUnpack(
                  tooltype="unpack",
                  adcthreshold=20,
                  maxfibers=8,
                  basegeom="CftBaseGeometry",
                  channelgeom="CftChannelGeometry",
                  realdata=FALSE)|
          SmtUnp L3TSmtUnpack(
                  chanthreshold=.03,
                  maxstrips=16,
                  basegeom="SiBaseGeometry",
                  channelgeom="SiChannelGeometry",
                  adcthreshold=10,
                  clusterthreshold=.03,
                  tooltype="unpack")|
  

• -data contains my edits for level2.sim-stripped, but no edits of level3.sim.
• A toollist.txt is provided which corresponds to this triggerlist but with the L3 unpack tools removed. Until we get a new version of Heptuple in p12 or p13 use this toollist to greatly reduce the crashes when producing the ntuple. Use the -l3toolist commandline option to pass this list to the executable.

global_CMT-8.20-data.tar

global_CMT-8.20-mc.tar

• -coor tarball is what comes out of COORSIM with no hand-edits.
• -data corresponds to editing level2.sim to add some missing lines.
• -mc corresponds to making the level2.sim correction and changing the level3.sim geometry management, CFTunp and SMTunp settings. The geometry is set to p10.06.01, edit this line yourself if your inputs are different.