4.2 Pin-to-Pin Connections

$\fbox{CB1}$

CN1F to CN6M

D Sub 37 Female D Sub 37 Male

Pin 1 -- Pin 1

Pin 37 -- Pin 37

$\fbox{CB2a: (two cables)}$

CN2-1F (first connector) to CN7M

D Sub 9 Female D Sub 37 Male

Pin 1 -- Pin 1

Pin 7 NOT CONNECTED Pin 7 CONNECTED TO THE EMERGENCY LINE ADAPTER BOARD ON D1 AND P1-UP STATIONS.NOT CONNECTED ON THE OTHER STATIONS.

Pin 8 -- Pin 20, 21, 22

Pin 9 -- Pin 23, 24, 25, 26

CN2-2F (second connector)

D Sub 9 Female

Pin 1 -- Pin 8

Pin 6 -- Pin 13

Pin 7 NOT CONNECTED

Pin 8 -- Pin 27, 28, 29

Pin 9 -- Pin 30, 31, 32

Note: There should be a flat cable extention (15m) D Sub 37 Male to D Sub 37 Female between CN7M to the Rack Monitor in some cases.

$\fbox{CB2b (four cables)}$

LVDT Signal Cond. to CN16M

Bottom terminals D Sub 37 Male

Pin 4 Center wire -- Pin 1

Pin 5 Mesh -- Pin 20

Pin 4 Center wire -- Pin 2

Pin 5 Mesh -- Pin 21

Pin 4 Center wire -- Pin 3

Pin 5 Mesh -- Pin 22

Pin 4 Center wire -- Pin 4

Pin 5 Mesh -- Pin 23

$\fbox{CB3}$ CN3F to Control Room Panic Button Card

Positive wire -- ?

Negative wire -- ?

$\fbox{CB4a}$

Micro switches to Index interface

CN9F to CN4M

D Sub 9 Female D Sub 9 Male (Index board side)

xxx Pin 1 Connect to Pin 6

xxx Pin 6 Connect to Pin 1

Pin 1(Gnd) -- Black -- Pin 6

Pin 2(L1) -- Red -- Pin 2

Pin 3(Gnd) -- Green -- Pin 7

Pin 4(L3) -- White -- Pin 3

$\fbox{CB4b}$

CN8F to CN4M

DIN5S (Female) D Sub 9 Male (The same above)

Pin 1 (Channel A)-- GREEN -- Pin 4

Pin 4 (+5V) -- WHITE -- Pin 5

Pin 5 (Gnd) -- BLACK -- Pin 8

Pin 3 (Channel B) -- RED -- Pin 9

$\fbox{CB4c}$

No Connector to CN8M

Hall sensor PCB DIN5P (Male)

Channel A -- GREEN -- Pin 1

+5V -- WHITE -- Pin 4

Gnd -- BLACK -- Pin 5

Channel B -- RED -- Pin 3

$\fbox{CB5}$

CN10M to CN5M

D Sub 25 Male D Sub 15 Male

Pin 24 -- Red-----Pin 1

Pin 25 -- Blue/red--Pin 9 (Gnd)

Pin 12 -- orange---Pin 2

Pin 25 -- White/orange-Pin 10 (Gnd)

Pin 13 -- Blue -- Pin 3

Pin 25 -- White/blue -- Pin 11 (Gnd)

Pin 19 + 560 ohms -- Green -- Pin 4 (Resistor inside D25 connector)

Pin 16 -- White/green -- Pin 5

Pin 9 -- Brown----Pin 6

Pin 21-- White/brown-Pin 14 (Gnd)

Pin 20 -- Gray -- Pin 8

Pin 25 -- White/gray -- Pin 7 (Gnd)

Pin 17 + Pin 25 (inside D25 connector)

$\fbox{CB6}$

No Connector to CN13M (5 Pins w/screws connector)

Motor Cable

A+ -- A+

A- -- A-

GND (green) -- GND

B+ -- B+

B- -- B-

See Driver Manual

$\fbox{CB7}$

CN12F to LVDT Signal Conditioner Top Terminals

Pin A -- Pin 9 Top

Pin B to Pin C togheter

Pin D -- Pin 7 Top

pin E -- Pin 8 Top

Pin F -- Pin 11 Top

Pin 10 Top to other units Pin 10 Top

$\fbox{CB8}$

DRIVER POWER to Filter

See Driver Instalation Manual

$\fbox{CB9}$

$\fbox{CB10}$

$\fbox{CB11}$

Home switch to other Home switch

CN11M to CN11M (Other unit in Ring Connection)

D Sub 9 Male D Sub9 Male

Pin 1 -- Pin 2 (N-1 unit)

Pin 2 -- Pin 1 (N+1 unit)